Network Appliance NetApp Certified Support Engineer

QUESTION NO: 1
You have severe database performance issues with a server connected to 8-Gb FC switches to storage. You know that the problem is not the storage because the QoS output indicates that the issue is outside the controller. You need to examine each piece of the chain, such as switch port status and the host contribution to latency.
In this scenario, which NetApp product would provide the required information?

A. OnCommand Insight B. OnCommand Unified Manager C. SnapDrive D. OnCommand Performance Manager

Correct Answer: D

QUESTION NO: 2
Which statement describes how memory and NVRAM are used by ONTAP during write requests?

A. The write request enters memory, a write acknowledgement is sent to the client, the request is passed to the partner's NVRAM, and data is written to disk. B. The write request enters memory and is passed to NVRAM and the partner's NVRAM, a write acknowledgement is sent to the client, and data is written to disk at the next consistency point. C. The write request enters NVRAM and is passed to the partner's NVRAM, data is written to disk, and a write acknowledgement is sent to the client. D. The write request enters memory and is passed to the partner's NVRAM, data is written to disk, and a write acknowledgement is sent to the client.

Correct Answer: D

QUESTION NO: 3
A customer recently performed an ONTAP upgrade and would like to confirm the successful completion of the process.
Which three actions would satisfy this requirement? (Choose three.)

A. Execute the version command at the cluster shell. B. A System Message notification will be shown upon reboot after a successful upgrade. C. Execute the system node upgrade-revert show command at the cluster shell. D. Execute the system node upgrade-revert show-task-status command at the cluster shell. E. Verify the version from the new AutoSupport that was automatically triggered after an upgrade.

Correct Answer: A,B,C

QUESTION NO: 4
A customer performed maintenance last weekend and power cycled both FAS8060 nodes of a 2-node ONTAP
9.2 cluster. The customer is concerned about port errors seen from the system ha interconnect port show command output.
Which two steps would you perform in troubleshooting this condition? (Choose two.)

A. Perform a takeover/giveback of both nodes. B. reset the counters using the system ha interconnect statistics clear-port command. C. Use the system ha interconnect flush command to manually reset the HA interconnect Link 0 and Link 1 on both nodes. D. Use the system ha interconnect link off/on command to manually reset the HA interconnect Link 0 and Link 1 on both nodes.

Correct Answer: A,D

QUESTION NO: 5
Click the Exhibit button.

An NFS client is failing to mount a volume exported by an SVM with the 10.64.82.96 IP address. The volume has a junction path of "/unix". The customer attempted to verify access rights by using the command shown in the exhibit.
In this scenario, what are two conclusions? (Choose two.)

A. The client has network connectivity to the SVM. B. The client is granted access to "/unix". C. The SVM only owns three volumes. D. The SVM's MOUNT RPC service is registered.

Correct Answer: A,C

QUESTION NO: 6
Click the Exhibit button.

Your customer's disks are showing 100% utilization, but the customer sees minimal user I/O. You collect statistics using the statit command over a 10-second time period as shown in the exhibit.
In this scenario, what is the problem?

A. Disk 0a.16 is faulty and should be replaced. B. The end users are doing a lot of reads on the SATA disks that are using vStorage APIs C. The network has too many multicast packets. D. Disk 0a.16 is being used to reconstruct data from a failed disk in the aggregate.

Correct Answer: C

QUESTION NO: 7
Click the Exhibit button.

You are creating a new LIF on a new SVM named "bravo-fs2". The cluster is being used in a multitenancy environment, and the bravo tenant has VLAN 105 assigned to it. You receive the error shown in the exhibit when you are creating the LIF. You have verified that the IP address is correct and the existing IP addresses that are already configured are also correct.
Referring to the exhibit, why is this error occurring?

A. Another device on VLAN 105 already has the IP address. B. Using the same IP address on two LIFs requires different IPspaces. C. Two NetApp LIFs cannot have the same IP address assigned. D. The network switch VLAN configuration is incorrect.

Correct Answer: D

Network Appliance NetApp Certified Support Engineer - NS0-192 Exam Questions