Juniper Service Provider Routing and Switching, Professional (JNCIP-SP)

QUESTION NO: 1
Exhibit:

R2 is receiving the same route from R1 and R3. You must ensure that you can load balance traffic for that route.
Referring to the exhibit, which two configuration changes will allow load balancing? (Choose two.)

A. Apply the prepend policy as an import policy under group R1. B. Configure multipath under group R1. C. Configure multipath under the global BGP configuration. D. Apply the prepend policy as an import policy under group R3.

Correct Answer: A,C

Explanation: Only visible for Pass4Test members. You can sign-up / login (it's free).

QUESTION NO: 2
Exhibit:

Traffic is being sent from R2 to R3. The link between R2 and R3 fails.
Referring to the exhibit, which statement is correct?

A. Manual intervention is required for traffic to be rerouted. B. Traffic will automatically reroute using the shortest path, which is R2 to R1 to R3. C. Traffic will automatically reroute distributed between all available paths. D. Traffic will automatically reroute using R2 to R4 to R1 to R3.

Correct Answer: D

QUESTION NO: 3
Exhibit:

All networks shown in the exhibit contain more than one BGP speaker You operate ISP A and must ensure that Customer Y sends their traffic to you over the directly connected link. Customer Y is not to be used for transit into your network.
What would you do to accomplish this task?

A. Advertise routes to Customer X with the well-known no-advertise community. B. Advertise routes to Customer X with the custom defined 0:0 community C. Advertise routes to Customer Y with the well-known no-export community D. Advertise routes to Customer Y with the custom defined 65535:65535 community.

Correct Answer: C

QUESTION NO: 4
Exhibit:

R2 is receiving a route from R1 and you must ensure that the route is not advertised to R3.
Referring to the exhibit, which two configurations on R2 will solve the issue? (Choose two.)

A. Apply the no-advertise policy as an import policy under group 65001. B. Apply the no-advertise policy as an export policy under group 65003. C. Apply the no-export policy as an import policy under group 65001. D. Apply the no-export policy as an export policy under group 65003.

Correct Answer: A,C

QUESTION NO: 5
Exhibit:

R4 is directly connected to both RPs (R2 and R3). R4 is currently sending all joins upstream to R3 but you want to load balance the joins between both RPs Referring to the exhibit, which configuration change will solve this issue?

A. Configure the join-load-balance parameter under PIM on R4. B. Configure the default route in inet.2 on R4 from R3 as the next hop to both R3 and R2. C. Configure the bootstrap priority on R2 to be the same as R3. D. Configure the group-range parameter to be the same on R2 and R3

Correct Answer: D

QUESTION NO: 6
Which statement is correct about BGP FlowSpec between a service provider's PE router and a customer?

A. The RFC deterministic traffic filtering algorithm is used by default in Junos. B. The flow routes received from a customer are limited to /32 masks for IPv4. C. The NLRI received from a customer is stored in the flowspec. inet .0 table. D. The NLRI received from a customer is stored in the inetfiow.0 table

Correct Answer: D

Explanation: Only visible for Pass4Test members. You can sign-up / login (it's free).

QUESTION NO: 7
Exhibit:

You are troubleshooting an issue where R1 is no longer receiving the default IS-IS route from R3.
Referring to the exhibit, which action would you take to solve the problem?

A. Delete the protocols isis level 2 disable configuration statement on R3. B. Delete the protocols isis import configuration statement on R1. C. Delete the protocols isis ignore-attached-bit configuration statement on R3. D. Delete the protocols isis ignore-attached-bit configuration statement on R1.

Correct Answer: D

QUESTION NO: 8
Exhibit.

Two CE devices (CE-1 and CE-2) belong to the same customer and connect into a single PE device (PE-1) However, the CE devices cannot communicate with each other You want to allow the CE devices to communicate with each other Referring to the exhibit, which action would solve the problem?

A. Configure both routing instances with the set routing-opt ions auto-export-statement B. Configure both routing instances with the vrf-table-label statement C. Configure both routing instances with the set routing-options autonomous-system loops 3 statement D. Configure both routing instances with the as-override statement within the BGP protocol

Correct Answer: A

QUESTION NO: 9
You are deploying a new EVPN service for your customers. You must build the service based on the following requirements
-- both Layer 2 and Layer 3 functionality must be supported
-- your customers must be able to support multiple VLANs in the same EVPN instance (EVI).
In this scenario which two types of routing instances should be configured? (Choose two.)

A. virtual switch B. VRF C. EVPN D. virtual router

Correct Answer: A,B

Explanation: Only visible for Pass4Test members. You can sign-up / login (it's free).

QUESTION NO: 10
Exhibit:

Which two statements regarding the output shown in the exhibit are correct? (Choose two.)

A. The label associated with this virtual circuit is out of range. B. The type of connection is remote. C. The PEs have matching control word values. D. The type of connection is local.

Correct Answer: B,C

Juniper Service Provider Routing and Switching, Professional (JNCIP-SP) - JN0-663 Exam Questions