EMC Dell PowerEdge Operate 2023 - D-PE-OE-23 Exam Questions
QUESTION NO: 1
A system board has been replaced on a Dell PowerEdge 16G server. What data can Easy Restore recover?
A system board has been replaced on a Dell PowerEdge 16G server. What data can Easy Restore recover?
Correct Answer: D
Explanation: Only visible for Pass4Test members. You can sign-up / login (it's free).
QUESTION NO: 2
Click the Launch Simulator button.
Using the iDRAC UI, what is listed as the Cache Memory Size for the H965i storage controller?
Note: It is necessary to close (x) the simulator window before you can select a response to this question.
Click the Launch Simulator button.
Using the iDRAC UI, what is listed as the Cache Memory Size for the H965i storage controller?
Note: It is necessary to close (x) the simulator window before you can select a response to this question.
Correct Answer: A
Explanation: Only visible for Pass4Test members. You can sign-up / login (it's free).
QUESTION NO: 3
A system administrator observes network connectivity issues with their iDRACs.
Which three commands can be used in the Diagnostic Console to troubleshoot this issue?
(Select 3)
A system administrator observes network connectivity issues with their iDRACs.
Which three commands can be used in the Diagnostic Console to troubleshoot this issue?
(Select 3)
Correct Answer: B,C,E
Explanation: Only visible for Pass4Test members. You can sign-up / login (it's free).
QUESTION NO: 4
A customer wants to optimize GPU density for maximum performance with high-capacity storage.
Which PowerEdge model should be recommended?
A customer wants to optimize GPU density for maximum performance with high-capacity storage.
Which PowerEdge model should be recommended?
Correct Answer: A
Explanation: Only visible for Pass4Test members. You can sign-up / login (it's free).
QUESTION NO: 5
A customer has relocated one of their Dell PowerEdge platform servers from their main data center to a remote edge location, which uses a different network segment.
Reconfigure the iDRAC network settings with the following information:
. IP Address (CIDR):
192.168.0.120 (/24)
. Gateway: 192.168.0.1
. DNS Server 1: 10.10.0.1
. DNS Server 2: 10.10.0.2
A customer has relocated one of their Dell PowerEdge platform servers from their main data center to a remote edge location, which uses a different network segment.
Reconfigure the iDRAC network settings with the following information:
. IP Address (CIDR):
192.168.0.120 (/24)
. Gateway: 192.168.0.1
. DNS Server 1: 10.10.0.1
. DNS Server 2: 10.10.0.2
Correct Answer:
See the Explanation for Step by Step solution.
Explanation:
To reconfigure the iDRAC network settings with a new IP address, gateway, and DNS servers, follow these steps in the iDRAC interface:
Step-by-Step Guide:
* Access iDRAC Network Settings:
* Log into the iDRAC interface.
* Go to the iDRAC Settings tab in the top menu.
* Select Network from the dropdown options. This will open the network configuration page.
* Change IP Address and Subnet Mask:
* In the Network settings, locate the section for IPv4 Settings.
* Set the IP Address to 192.168.0.120.
* For the Subnet Mask, since it's a /24 CIDR, set it to 255.255.255.0.
* Configure the Gateway:
* In the same section, find the field for Default Gateway.
* Enter the Gateway as 192.168.0.1.
* Update DNS Server Information:
* Scroll down to the DNS Server settings.
* Enter DNS Server 1 as 10.10.0.1.
* Enter DNS Server 2 as 10.10.0.2.
* Apply the Settings:
* After entering all the new network information, click on Apply or Save to confirm the changes.
* The iDRAC interface may prompt for a restart to apply network changes. Follow any prompts as needed.
* Verify the Configuration:
* After applying the changes, check that the iDRAC is accessible at the new IP address
192.168.0.120.
* Confirm that the gateway and DNS settings are properly configured by testing connectivity or accessing the iDRAC from a device within the same network segment.
By completing these steps, you will have reconfigured the iDRAC network settings for the new network segment, allowing remote management of the Dell PowerEdge server at the edge location.
Explanation:
To reconfigure the iDRAC network settings with a new IP address, gateway, and DNS servers, follow these steps in the iDRAC interface:
Step-by-Step Guide:
* Access iDRAC Network Settings:
* Log into the iDRAC interface.
* Go to the iDRAC Settings tab in the top menu.
* Select Network from the dropdown options. This will open the network configuration page.
* Change IP Address and Subnet Mask:
* In the Network settings, locate the section for IPv4 Settings.
* Set the IP Address to 192.168.0.120.
* For the Subnet Mask, since it's a /24 CIDR, set it to 255.255.255.0.
* Configure the Gateway:
* In the same section, find the field for Default Gateway.
* Enter the Gateway as 192.168.0.1.
* Update DNS Server Information:
* Scroll down to the DNS Server settings.
* Enter DNS Server 1 as 10.10.0.1.
* Enter DNS Server 2 as 10.10.0.2.
* Apply the Settings:
* After entering all the new network information, click on Apply or Save to confirm the changes.
* The iDRAC interface may prompt for a restart to apply network changes. Follow any prompts as needed.
* Verify the Configuration:
* After applying the changes, check that the iDRAC is accessible at the new IP address
192.168.0.120.
* Confirm that the gateway and DNS settings are properly configured by testing connectivity or accessing the iDRAC from a device within the same network segment.
By completing these steps, you will have reconfigured the iDRAC network settings for the new network segment, allowing remote management of the Dell PowerEdge server at the edge location.
QUESTION NO: 6
When does configuration validation run?
When does configuration validation run?
Correct Answer: D
Explanation: Only visible for Pass4Test members. You can sign-up / login (it's free).
