EMC Dell PowerEdge Operate v2 - D-PE-OE-01 Exam Questions
QUESTION NO: 1
What is the recommended option to use when applying firmware to a replaced part using the Lifecycle Controller?
What is the recommended option to use when applying firmware to a replaced part using the Lifecycle Controller?
Correct Answer: C
QUESTION NO: 2
What are two ways to check on the health status of a server?(Select 2)
What are two ways to check on the health status of a server?(Select 2)
Correct Answer: A,D
QUESTION NO: 3
A technician tries to power on a server but nothing happens when they press the power button. The status LEDs on both PSUs are green. The technician is able to connect to the iDRAC to review the System Event Logs and discovers that PSU2 has failed.
A technician tries to power on a server but nothing happens when they press the power button. The status LEDs on both PSUs are green. The technician is able to connect to the iDRAC to review the System Event Logs and discovers that PSU2 has failed.
Correct Answer: C
QUESTION NO: 4
What is required for iDRAC Direct 2.0 to connect with IDRAC9 interfaces such as RACADM and WSMAN?
What is required for iDRAC Direct 2.0 to connect with IDRAC9 interfaces such as RACADM and WSMAN?
Correct Answer: B
QUESTION NO: 5
A system administrator is trying to connect with a mobile device to a Dell PowerEdge 16G server using Quick Sync 2. They failed to make a connection.
What is the reason for the failure?
A system administrator is trying to connect with a mobile device to a Dell PowerEdge 16G server using Quick Sync 2. They failed to make a connection.
What is the reason for the failure?
Correct Answer: A
QUESTION NO: 6
A technician needs to analyze a server that is using more power than expected. The server is part of a cluster that runs jobs between 8 AM and 5 PM. The cluster is not used at other times of the day. The server runs an unsupported OS. Performance while jobs are running is a key consideration.
Which option should the technician choose from within System Profile Settings within System Setup to address this issue?
A technician needs to analyze a server that is using more power than expected. The server is part of a cluster that runs jobs between 8 AM and 5 PM. The cluster is not used at other times of the day. The server runs an unsupported OS. Performance while jobs are running is a key consideration.
Which option should the technician choose from within System Profile Settings within System Setup to address this issue?
Correct Answer: C
QUESTION NO: 7
A PowerEdge server is running critical production workloads and has passed all validation and compliance checks. The security team requires that no unauthorized or accidental changes be made to the system configuration during the production phase. Later, the administrator attempts to update the BIOS remotely using iDRAC but the operation fails without applying any changes. Which is the most likely reason for this behavior?
A PowerEdge server is running critical production workloads and has passed all validation and compliance checks. The security team requires that no unauthorized or accidental changes be made to the system configuration during the production phase. Later, the administrator attempts to update the BIOS remotely using iDRAC but the operation fails without applying any changes. Which is the most likely reason for this behavior?
Correct Answer: A
Explanation: Only visible for Pass4Test members. You can sign-up / login (it's free).
QUESTION NO: 8
SIMULATION
A system administrator is asked to create an iDRAC shared management port using LOM2 and create a failover network using LOM3.
Use the simulator to accomplish this task.
SIMULATION
A system administrator is asked to create an iDRAC shared management port using LOM2 and create a failover network using LOM3.
Use the simulator to accomplish this task.
Correct Answer:
Answer in Explanation
Explanation:
To configure an iDRAC shared management port with LOM2 and set up a failover network using LOM3 in the iDRAC interface, follow these steps:
Step-by-Step Guide:
Access iDRAC Network Settings:
In the iDRAC interface, navigate to the iDRAC Settings tab in the top menu bar. Select Network from the dropdown options to access network configuration settings. Configure the Shared Management Port:
In the Network settings, locate the section for Network Interface or LAN Interface Configuration. Change the NIC Selection to Shared. This will enable the use of a LAN on Motherboard (LOM) port for iDRAC management.
Select LOM2 for the Shared Management Port:
Once you've selected Shared, additional options should appear for selecting the specific port. Choose LOM2 as the Shared Management Port. This configures iDRAC to use LOM2 for its primary network connection.
Enable Failover and Select LOM3:
Look for the Failover settings within the same Network Interface configuration.
Enable Failover and select LOM3 as the failover network port. This configuration allows iDRAC to switch to LOM3 automatically if there is an issue with the connection on LOM2.
Save and Apply Settings:
Once you have configured the shared management port and failover settings, click Apply or Save to confirm the configuration.
The iDRAC interface may briefly refresh, and you should receive a confirmation that the settings have been applied successfully.
Verify Configuration:
After the settings are saved, you can verify that LOM2 is listed as the shared management port and that LOM3 is set as the failover port under Network settings.
By following these steps in the simulator, you should be able to configure iDRAC to use LOM2 for the shared management port and set up a failover network with LOM3. Make sure to save your changes to apply the configuration.
Explanation:
To configure an iDRAC shared management port with LOM2 and set up a failover network using LOM3 in the iDRAC interface, follow these steps:
Step-by-Step Guide:
Access iDRAC Network Settings:
In the iDRAC interface, navigate to the iDRAC Settings tab in the top menu bar. Select Network from the dropdown options to access network configuration settings. Configure the Shared Management Port:
In the Network settings, locate the section for Network Interface or LAN Interface Configuration. Change the NIC Selection to Shared. This will enable the use of a LAN on Motherboard (LOM) port for iDRAC management.
Select LOM2 for the Shared Management Port:
Once you've selected Shared, additional options should appear for selecting the specific port. Choose LOM2 as the Shared Management Port. This configures iDRAC to use LOM2 for its primary network connection.
Enable Failover and Select LOM3:
Look for the Failover settings within the same Network Interface configuration.
Enable Failover and select LOM3 as the failover network port. This configuration allows iDRAC to switch to LOM3 automatically if there is an issue with the connection on LOM2.
Save and Apply Settings:
Once you have configured the shared management port and failover settings, click Apply or Save to confirm the configuration.
The iDRAC interface may briefly refresh, and you should receive a confirmation that the settings have been applied successfully.
Verify Configuration:
After the settings are saved, you can verify that LOM2 is listed as the shared management port and that LOM3 is set as the failover port under Network settings.
By following these steps in the simulator, you should be able to configure iDRAC to use LOM2 for the shared management port and set up a failover network with LOM3. Make sure to save your changes to apply the configuration.
QUESTION NO: 9
A company has an existing Dell EMC 4-node X410 Gen 5 cluster with approximately 100TB of SMB shares connected using two InfiniBand 8-port switches.
The company wants a technical refresh of the cluster with a new 4-node H500 Gen 6 cluster with two 16-port InfiniBand switches. The existing cluster has SyncIQ, SmartConnect Advanced, and SmartPools licenses installed.
To move the data from the existing modes to the new nodes, which migration plan is recommended?
A company has an existing Dell EMC 4-node X410 Gen 5 cluster with approximately 100TB of SMB shares connected using two InfiniBand 8-port switches.
The company wants a technical refresh of the cluster with a new 4-node H500 Gen 6 cluster with two 16-port InfiniBand switches. The existing cluster has SyncIQ, SmartConnect Advanced, and SmartPools licenses installed.
To move the data from the existing modes to the new nodes, which migration plan is recommended?
Correct Answer: A
QUESTION NO: 10
What is a key feature of Part Replacement in Lifecycle Controller?
What is a key feature of Part Replacement in Lifecycle Controller?
Correct Answer: A
QUESTION NO: 11
A technician needs to configure the Lifecycle Controller network settings with a static IP address. A limited number of static IP addresses are available for use.
Which previously assigned IP address can also be used for the Lifecycle Controller?
A technician needs to configure the Lifecycle Controller network settings with a static IP address. A limited number of static IP addresses are available for use.
Which previously assigned IP address can also be used for the Lifecycle Controller?
Correct Answer: C
