SAP Certified Application Associate - Production - Planning & Manufacturing with SAP ERP 6.0 EHP4

QUESTION NO: 1
In the SAP ECC system, a material is produced with the help of production orders. Though originally used for rate-based planning only, the planning table is to be used to plan this material. On the initial screen of the planning table, you select this material and then receive a message informing you that you cannot use the planning table for this material.
Which one of the following reasons for this message applies?

A. There are no requirements present. B. The series production indicator has not been set. C. There is no valid production version for this material. D. There are no planned orders or production orders present.

Correct Answer: C

QUESTION NO: 2
An enterprise wants to use SAP ECC requirements planning together with the NETPL procedure (net change planning in the planning horizon). The planning horizon is to be set equally for all materials by default. However, some materials are to be given a different planning horizon.
What procedure would you recommend to the project team for setting the planning horizon on the system side?

A. The planning horizon is set in the MRP groups in Customizing and the variant values are stored in the material masters for the materials in question. B. The planning horizon is set in the plant parameters in Customizing and variant entries are stored in the material masters for the materials in question. C. The planning horizon is set in Customizing using the plant parameter setting and variant entries are assigned via the MRP groups for the materials in question. D. The planning horizon is set in the MRP groups in Customizing and variant entries are assigned via the plant parameter settings.

Correct Answer: C

QUESTION NO: 3
With which functions of the process order can you fulfill the requirements of the Good Manufacturing Practices (GMP) standard? (Choose three.)

A. Digital signature B. Availability check C. Resource selection D. Material identification and reconciliation E. Batch record

Correct Answer: A,D,E

QUESTION NO: 4
A finished material is to be planned in a controlled manner in the SAP ECC system in the context of requirements planning. The planned orders are scheduled using what is known as basic date scheduling (not lead-time scheduling). Which of the following statements is true for the resulting dependent requirements?

A. When a customer order is created for the finished product, the dependent requirements are automatically triggered for the components in the bill of material without a planning run. B. In multi-level backward scheduling, dependent requirements are triggered at the start date for the higher-level assembly planned order. C. In multi-level backward scheduling, dependent requirements are triggered at the start date for the higher-level assembly. D. If individual material components are explicitly assigned to operations during BOM and routing maintenance, the requirement dates of the dependent requirements for these components are scheduled at each of the operation start dates.

Correct Answer: C

QUESTION NO: 5
Which of the following possible errors would lead to the message shown? (Choose two.)

A. There are no valid routings or no routings available on the explosion date. B. The material master (product) is set to manual routing selection and valid routing exists. C. In the material master, plan selection was set to production version. A production version was created and it is faulty. D. The Customizing for the order type is set to manual routing selection and a valid routing exists.

Correct Answer: A,C

QUESTION NO: 6
Which of the following statements about ATP (Available To Promise) checks for material components are correct? (Choose two.)

A. ATP checks are mandatory for lead-time scheduling. B. ATP checks can be adjusted to also consider future requirements and receipts. C. ATP checks are automatically performed during MRP (Material Requirements Planning) runs. D. ATP checks can be carried out automatically when releasing a production order. E. ATP checks are used to evaluate the free capacity on a certain work center.

Correct Answer: B,D

QUESTION NO: 7
When maintaining a work center, formulas can be assigned in the scheduling view. Formulas use formula parameters for calculation. What can be the origin of the formula parameters used for scheduling? (Choose three.)

A. General operation values in task list B. General item values in bill of materials C. General values from work scheduling view in the material master D. User-defined field from operation in task list E. Standard value from operation in task list

Correct Answer: A,D,E

QUESTION NO: 8
Which of the following structural elements does a process order have? (Choose three.)

A. Relationships B. Item data C. Phases D. Characteristic-based process instructions E. Parallel sequences

Correct Answer: A,C,D

SAP Certified Application Associate - Production - Planning & Manufacturing with SAP ERP 6.0 EHP4 - C_TSCM42_64 Exam Questions