Cisco Designing Cisco Enterprise Wireless Networks - 300-425 Exam Questions

QUESTION NO: 1
An architect configures a set of AirOS controllers to be in the same mobility group as the existing controllers. The implementation should facilitate inter-controller roaming for users in their new campus. After the configuration, the mobility tunnel is not operational for the data path in the network. Which two validations should be performed? (Choose two.)

QUESTION NO: 2
An engineer is conducting a Layer 2 site survey.
Which type of client must the engineer match to the survey?

QUESTION NO: 3
An engineer changed me TPC Power Threshold for a wireless deployment from the default value to 65 dBm. The engineer conducts a new post deployment survey to validate the results.
What is the expected outcome?

QUESTION NO: 4
An engineer is designing a new wireless network for an international company. The design must have these requirements:
- broadcast wireless channels based on country regulations
- controllers to support APs for regulatory domains
- RF changes applied on APs per country that are installed
- multiple-country feature to be used on the controllers
Which design approach must be taken?

QUESTION NO: 5
An engineer must optimize client roaming after noticing that clients in the environment are not roaming as expected. Upon reviewing an over-the-air packet capture, the engineer sees that the AP is sending a BSS Transition Management query to the client, which causes it to roam. The disassociation imminent feature is not enabled on the WLAN. What is the cause of the issue?

QUESTION NO: 6
Refer to the exhibit. A company has a foreign Cisco WLC named WLC1 and two anchor WLCs named WLC2 and WLC3 that all run version 8.10.x code. The company wants to configure the priority for one of the WLANs with WLAN-id #5 so that WLC1 always has WLC2 as its primary anchor for WLAN-id #5. Which command must be incorporated in the design to meet the requirement?

QUESTION NO: 7
A network engineer is designing a new wireless network.
The network needs to have these characteristics:
- support high client concentration
- optimize client performance
- avoid interference
Which approach should be taken?

QUESTION NO: 8
In a stadium deployment, which WLAN design approach is most recommended?

QUESTION NO: 9
What is the main purpose of conducting a post-deployment site survey?

QUESTION NO: 10
An engineer is using Ekahau Site Survey to create a WLAN plan for a warehouse. The plan is to use patch antennas. Which setting is adjusted when simulated APs are placed on the map?

QUESTION NO: 11
Clustering Cisco WLCs into a single RF group enables the RRM algorithms to scale beyond the capabilities of a single Cisco WLC.
How many WLC and APs in an RF group can the controller software scale up to in WLC release
8.9 depending on the platform?

QUESTION NO: 12
A rapidly expanding company has tasked their network engineer with wirelessly connecting a new cubicle area with Cisco workgroup bridges until the wired network is complete. Each of 42 new users has a computer and VoIP phone.
How many APs for workgroup bridging must be ordered to keep cost at a minimum while connecting all devices?

QUESTION NO: 13
A customer uses a Cisco Catalyst 9800 Series wireless controller to manage all of the APs for a campus network. Secure guest access is required for the guest network. A Cisco 5520 anchor controller is deployed within a DMZ. Which design approach ensures that the mobility tunnel is established successfully between the wireless controller and the anchor controller?

QUESTION NO: 14
A customer is planning to replace older access points with Cisco 4800 Series Access Points.
Unaware of the infrastructure requirements, the client has an engineer investigate the inline power requirement. Which IEEE 802.3 standard complies with the Cisco 4800 Series Access Points?

QUESTION NO: 15
A customer has a centralized wireless deployment with N+1 high availability and few open authentication SSIDs configured. After failover, all APs are broadcasting all SSIDs, but the clients are assigned IP addresses from a different subnet. The WLANs on both WLCs are configured with the same dynamic interfaces. Which feature must be incorporated in the wireless design of the second controller?