Cisco Implementing Cisco Wireless Advanced Solutions

QUESTION NO: 1
What is the mandatory bandwidth requirement for connecting Cisco Spaces Connector to Cisco Spaces?

A. 8 Mbps B. 4 Mbps C. 250 Kbps D. 2 Mbps

Correct Answer: B

QUESTION NO: 2
An engineer has successfully implemented 10 active RFID tags in an office environment. The tags are not visible when the location accuracy is tested on the Cisco CMX Detect and Locate window.
Which setting on Cisco CMX allows the engineer to view the tags?

A. Enable hyperlocation services for RFI B. Enable probing clients for active tags. C. Enable RFID tags in tracking options. D. Define an RFID group globally and add the tags.

Correct Answer: C

QUESTION NO: 3
What type of packets are sent from one source host address to a special group-based destination address?

A. Unicast B. Anycast C. Broadcast D. Multicast

Correct Answer: D

QUESTION NO: 4
A wireless engineer must configure access control on a WLC using a TACACS+ server for a company that is implementing centralized authentication on network devices.
Which role value must be configured under the shell profile on the TACACS+ server for a user with read-only permissions?

A. READ B. MANAGEMENT C. ADMIN D. MONITOR

Correct Answer: D

QUESTION NO: 5
What are key differences between CWA and LWA? (Choose two.)

A. LWA uses Layer 3, whereas CWA uses a mixture of Layer 2 and Layer 3. B. LWA uses Layer 2 only, whereas CWA uses Layer 3 only. C. LWA uses MAC filtering, whereas CWA does not. D. CWA uses MAC filtering, whereas LWA does not.

Correct Answer: A,D

QUESTION NO: 6
A network engineer is configuring a Cisco switch for 802.1X authentication.
Following is a snippet of the commands he entered on the switch:
aaa new-model
!
aaa authentication dot1x default group radius
!
<?????>
!
radius server ISE
address ipv4 10.48.39.161 auth-port 1645 acct-port 1646
key 7 123A0C0411045D5679
!
interface GigabitEthernet0/15
switchport access vlan 123
switchport mode access
authentication order dot1x
authentication port-control auto
dot1x pae authenticator
spanning-tree portfast edge
What command is represented by <?????> ?

A. dot1x system enable B. enable dot1x auth-control C. dot1x system-auth-control D. 802.1X auth-control

Correct Answer: C

QUESTION NO: 7
An engineer set up identity-based networking with ISE and configured AAA override on the WLAN.
Which two attributes must be used to change the client behavior from the default settings? (Choose two.)

A. DNS server B. IPv6 ACL C. multicast address D. DSCP value E. DHCP timeout

Correct Answer: B,D

QUESTION NO: 8
What is the primary role of the QoS profile in AireOS?

A. Sets the UP-to-DSCP and marking scheme B. Sets the DSCP trust boundary C. Allows customization of the EDCA parameters for QoS handling D. Sets a maximum allowable DSCP value that can be used on the CAPWAP header and downstream UP value

Correct Answer: D

QUESTION NO: 9
Which feature on a Cisco wireless LAN controller keeps track of and delivers IPv6 multicast flows to the clients that request them, thus avoiding the need to forward each IPv6 multicast client packet to the wired network?

A. Internet Group Management Protocol (IGMP) B. Multicast Listener Discovery (MLD) snooping C. Protocol Independent Multicast (PIM) D. IGMP snooping

Correct Answer: B

QUESTION NO: 10
Which of the following statements correctly describes the difference between Catalyst 9800 and AireOS ACLs?

A. On a Catalyst 9800, traffic that is permitted by the redirection ACL causes redirection to the redirection URL. B. On a Catalyst 9800, traffic that is denied by the WebAuth ACL causes redirection to the redirection URL. C. On a Catalyst 9800, traffic that is permitted by the HTTP ACL causes redirection to the redirection URL. D. On a Catalyst 9800, traffic that is denied by the redirection ACL causes redirection to the redirection URL.

Correct Answer: A

Cisco Implementing Cisco Wireless Advanced Solutions - 300-120 Exam Questions